DN NA Class  

DN America Forums

March 28, 2024, 04:08:15 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Login Register  
Pages: [1]
  Print  
Author Topic: Bent Struble Chock  (Read 17353 times)
RLinden
Newbie

Posts: 9


« on: December 21, 2013, 10:11:24 PM »

While getting the boat back together after two seasons off I found one of my chocks to be bent.

A few years ago I switched to cutaway struble chocks.  They are glued to my plank. While shimming one of my runners I found that it was rocking back and forth in the horizontal axis.  After some experimentation with some 1in aluminum angle I have found that a 1mm crown is present.  I have attached a picture. 

Has anyone else experienced a bent struble chock?

Any input on how I should fix it or what to do next would be helpful.

What to do next?
1. Don't worry about it.
2. Replace with new chocks and reglue.
3. Have it machined straight and reglue.

Thank you,

Rob Linden DN 5174
Logged
NICK VITALE
Class Member
*
Posts: 7


« Reply #1 on: December 21, 2013, 10:36:58 PM »

Where's the picture?
Logged
RLinden
Newbie

Posts: 9


« Reply #2 on: December 21, 2013, 10:48:44 PM »

Chock photo
Logged
RLinden
Newbie

Posts: 9


« Reply #3 on: December 21, 2013, 10:49:58 PM »

Chock Photo 2
Logged
Bob Rast DN1313
Newbie

Posts: 148



WWW
« Reply #4 on: December 22, 2013, 08:40:39 AM »

I straightened some Sarns chocks , not as beefy as the Struble but may work.
I put a bolt through the center with nuts on inside against both sides inside of  the chock or you could use some kind of block .  to keep that dimension, and used large Machine clamp  and  brought both outside edges back to same dimension as center .
Or you could just shim the inside of the chock fo a quick fix

Bob Rast
DN1313
Logged
Bob Rast DN1313
Newbie

Posts: 148



WWW
« Reply #5 on: December 22, 2013, 08:52:41 AM »

You might want to check your other chock with a micrometer, the center of chock is sometimes wider so runner only touches outside edges of chock.  A large clamp should work just take your time  and check as you go .
Logged
RLinden
Newbie

Posts: 9


« Reply #6 on: December 22, 2013, 09:27:19 AM »

The other chock is straighter but still not as straight as my old sarns chocks they replaced.  The middle section by the bolt is the tight spot in the chock.  This allows the runner to wobble back and forth.  I have only sailed on them a half dozen times or so since putting them on the plank. 

I think I may be able to straighten a sarns chock but the web design of the struble may be tough.

Thank you for the help
Logged
Bob Rast DN1313
Newbie

Posts: 148



WWW
« Reply #7 on: December 22, 2013, 06:26:01 PM »

Its aluminum already bent once might as well try to straighten , experiment on the Sarns   I think  the center should be slightly wider than ends or the same ,Ill check my extruded chocks
and see what they are

You could just shim that side of the chock with some shim tape
Logged
Rolley
Newbie

Posts: 9


« Reply #8 on: December 23, 2013, 09:05:55 AM »

Sorry if this is totally irrelevant. My Iceflyer really mangles Sarns chocks. Also, I never could solve the aluminum on aluminum wear issue on the Sarns runner stiffener.  I went with soft steel with a much larger base (nine through bolts).  A season of abuse will result in a slight splay, which I fix with about five minutes of vice work.  Local welders make these for about $30/pair.
Logged
Geoff Sobering
Class Officer
***
Posts: 461



WWW
« Reply #9 on: December 23, 2013, 10:16:10 AM »

If you decide to replace your chocks, I highly recommend Wes Wilcox's milled chocks.
He has an ad in Runner Tracks: http://runnertracks.org/2013/winter/Runner%20Tracks%20Dec%202013.pdf#page=13
Logged

Man Why You Even Got to Do a Thing
Bob Rast DN1313
Newbie

Posts: 148



WWW
« Reply #10 on: December 23, 2013, 04:23:53 PM »

Saw those at the swap meet looks like a great product

Bob Rast
DN1313
Logged
RLinden
Newbie

Posts: 9


« Reply #11 on: December 23, 2013, 10:23:00 PM »

I will probably try the shimming idea once I have some time available in the shop. 

What glue do you use to attach the shims to the runner body?
Logged
Geoff Sobering
Class Officer
***
Posts: 461



WWW
« Reply #12 on: December 23, 2013, 11:24:49 PM »

What glue do you use to attach the shims to the runner body?

I've used superglue with fiberglass/epoxy shims, and now I use double-sided tape with plastic shim stock.
Logged

Man Why You Even Got to Do a Thing
Ken Smith
ADMIN

Posts: 289


sail often, travel light


« Reply #13 on: January 01, 2014, 06:02:57 AM »

All the energy of you and the boat tries to go straight when your runner is caught in a crack. Something has to give. The advantage of glued chocks is persistent alignment. This is one disadvantage.
I recommend new chock here.
Logged

Ken Smith
DN4137US
Bob Gray
Class Member
*
Posts: 194


« Reply #14 on: January 01, 2014, 08:12:21 AM »

RLinden I tried your email address on the DN registery but it came back. Send me your email and I'll send you an article I'm working on for a fix. My email is bgray4654@ yahoo.com
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1 RC3 | SMF © 2001-2006, Lewis Media Valid XHTML 1.0! Valid CSS!